Ashcroft ATE-100 Handheld LCD Digital Calibrator Manual de usuario Pagina 3
- Pagina / 80
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
- 3 -
Revision 4.6 3/2004
Table of Contents
Section Description Page
1.0 Introduction ................................................................................................................................. 4
1.3 Base Unit Overview ........................................................................................................ 4
1.4 Quick Select Module Overview ..................................................................................... 4
1.4.1 The GQS-1 Quick Select Pressure Module ................................................................ 5
1.4.2 The GQS-2 Quick Select Pressure Module . .............................................................. 5
1.4.3 The GQS-RT1 Quick Select RTD Temperature Interface Module ............................. 5
1.4.4 The GQS-TC1 Quick Select Thermocouple Interface Module .................................. 6
2.0 Unpacking .................................................................................................................................... 6
2.1 Unpacking Product Upon Receipt ................................................................................... 6
2.2 Product Storage ............................................................................................................... 6
2.3 Product Cleaning ............................................................................................................ 6
3.0 System Start-Up General Instructions ...................................................................................... 6
3.1 Battery Installation .......................................................................................................... 6
3.2 Installation of Quick Select Modules .............................................................................. 7
3.3 Starting Up HHC System ................................................................................................ 7
3.4 Optional System Start Up Procedures ............................................................................. 8
3.4.1 Auto Off – Battery Save Function .............................................................................. 8
3.4.2 Set Up for Battery Charge Level Indication ............................................................... 9
3.4.3 Low Battery Icon ........................................................................................................ 10
3.4.4 Programming Date and Time Information ................................................................. 10
3.4.5 Input of Owner/Operator Information ........................................................................ 11
3.5 Removing Quick Select Modules .................................................................................... 12
4.0 Key Function Overview ............................................................................................................... 12
5.0 Port Select Function ................................................................................................................... 13
6.0 Zero Function .............................................................................................................................. 14
6.1 Zeroing One of Two Installed Quick Select Pressure Module ........................................ 14
7.0 Displaying Current & Voltage Measurements ........................................................................... 14
8.0 Engineering Unit Selection ......................................................................................................... 15
8.1 Selecting a Factory Programmed Engineering Unit ........................................................ 15
8.2 Setting Up a Custom (User Defined) Engineering Unit .................................................. 15
8.3 Using a Custom (User Defined) Engineering Unit .......................................................... 16
8.4 Display of Two Different Engineering Units, for Two Installed Modules ...................... 17
8.5 Temperature Selection for H2O Conversion Factor ........................................................ 18
9.0 Tare Function ............................................................................................................................... 19
10.0 Hold Function .............................................................................................................................. 19
10.1 Using the Hold Function ................................................................................................. 19
11.0 Minimum and Maximum Value Tracking .................................................................................... 20
- HAND HELD 1
- CALIBRATOR 1
- OPERATING 1
- Table of Contents 3
- — APPENDICES — 5
- Section 1.0 Introduction 6
- Overview 6
- temperature performance 10
- Eng Unit Eng Unit 10
- +xx.xxx +xx.xxx 10
- Revision 4.6 3/2004 11
- JOHN Q OPERATOR 14
- Ent=OK CE=Cancel 14
- Velocity Volume 25
- π = 3.141592 27
- 2 α392 ∠200/850 34
- 3 Ni Minco (Ni 120Ω) 34
- Disable Manual 37
- Deadband 37
- Ref temperature 37
- Disable Manual 39
- +x.xxV +xx% 44
- DATA 47
- Disable ISO1745 58
- Journal Inquiry 58
- Calib RTmodule 62
- Access code ? 62
- .00000 62
- 12345 62
- ±50 microvolts 63
- (5% increments) 69
- (10% increments and zero) 69
- (20% increments and zero) 69
- (25% increments and zero) 69
- - 70- Revision 4.6 3/2004 70
- - 74- Revision 4.6 3/2004 74
- SYSTEM ACCURACY WITH 76
- TABLE II 76
- APPENDIX D 77
- RTD PROBE CONNECTOR 77
- APPENDIX E 78
- - 80- Revision 4.6 3/2004 80
Relacionado con productos y manuales para Instrumentos de medición Ashcroft ATE-100 Handheld LCD Digital Calibrator
(7 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.071 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales